Ir al contenido
  1. Todos los productos
  2. Adhesives
  3. Cartridges
  4. Akemi MATCH BOND - 1155 White Linen - Methacrylate Pre-Pigmented Cartridge Adhesive (250 mL)
  5. Cartridges
Lista de precios: General Price List (USD) Lista de precios
Lista de precios: General Price List (USD) Lista de precios
Akemi MATCH BOND - 1155 White Linen - Methacrylate Pre-Pigmented Cartridge Adhesive (250 mL)

Akemi Match Bond 1155 White Linen — Pre-Pigmented Cartridge Adhesive (250 mL)

AKEMI® Match Bond (Colour Bond CC) is a pre-colored, gel-like two-component adhesive that produces strong, near-invisible seams in engineered and natural stone. This cartridge is factory-pigmented in shade 1155 “White Linen” to blend into matching light stone, so the glue line disappears. Dispensed straight from a 250 mL cartridge through a static mixer nozzle, it has high bonding power, very fast surface drying, and a non-sag gel body that holds on vertical joints. AKEMI offers this adhesive in an extensive color-match range keyed to leading engineered-stone brands.

  • Pre-pigmented “White Linen” (1155) — ready-matched for invisible seams
  • Two-component cartridge — dispensed through a static mixer nozzle
  • High bonding power with very fast surface drying
  • Gel-like & non-sag — holds on vertical joints
  • For engineered & natural stone; resistant to water, petrol, and mineral oils
Property Detail
Brand Akemi
Manufacturer AKEMI GmbH, Nuremberg, Germany
Product Type Pre-colored, two-component cartridge adhesive (Colour Bond CC)
Chemical Basis Two-component epoxy-acrylate
Consistency Gel-like, non-sag
Color White Linen (color code 1155)
Mixing Ratio 10 : 1 (via static mixer nozzle)
Working Time Approx. 5–7 minutes at 68°F (20°C)
Temperature Resistance Good adhesion up to 140–158°F (60–70°C); briefly higher under low strain
Resistance Resistant to water, petrol, and mineral oils
Cartridge Size 250 mL
Color Range Over 50 colors matched to leading engineered-stone brands
  • Pre-colored to shade 1155 “White Linen” for near-invisible seams
  • High bonding power with very fast surface drying and easy processability
  • Gel-like, non-sag body holds position on vertical joints
  • Good adhesion on engineered stone as well as natural and artificial stone, even at elevated temperatures
  • Resistant to water, petrol, and mineral oils
  • Part of an extensive color-match system for stone fabrication

Producing strong, color-matched, near-invisible joints and seams in engineered stone (engineered marble and quartz) as well as natural and artificial stone. Ideal for countertop seaming, edge build-ups, and repairs where the glue line should blend into light stone.

Choose the color code that matches the stone; AKEMI publishes recommended codes by material and brand.

  1. Make sure the surfaces to be bonded are clean, dry, and free of grease and dust.
  2. Fit the cartridge in a suitable dispensing gun and attach a fresh static mixer nozzle; the adhesive mixes at a 10 : 1 ratio as it is dispensed.
  3. Dispense a little to purge until the color is uniform, then apply to the joint.
  4. Assemble the parts and support the joint. The adhesive stays workable for approx. 5–7 minutes at 68°F (20°C); warmth shortens and cold lengthens this time.
  5. Remove excess before it sets. Once cured, seams can be worked flush.
  • Reactive two-component adhesive with a strong odor — use only with good ventilation.
  • Keep away from heat, sparks, and open flame; avoid skin and eye contact.
  • Use a fresh static mixer nozzle for each cartridge to ensure correct mixing.
  • Industrial chemical product — wear chemical-resistant gloves and eye protection. Always consult the AKEMI Safety Data Sheet (SDS) before use.

Industrial two-component adhesive. Keep away from ignition sources and use only in well-ventilated areas. Wear chemical-resistant gloves and eye protection. Consult the AKEMI Safety Data Sheet (available from the manufacturer or stein.akemi.de) before use. Technical values are manufacturer figures at 68°F (20°C) and may vary with jobsite conditions.