A polishing head cannot reach everywhere. Inside corners, carved reliefs, lettering, the back face of a frame, a rough-ground edge tucked under an overhang — every shop runs into surfaces where the machine simply cannot get a pad flat against the stone, no matter how small the diameter. AKEMI® Super Gloss was built for exactly that gap: a solvent-based, brush- or roller-applied lacquer that brings a high-gloss, color-intensified finish to rough, ground and porous stone by hand, without a polisher ever touching the area.
Dynamic Stone Tools stocks AKEMI Super Gloss in a 750 mL bottle, and this spotlight works from AKEMI's own technical data sheet for the product rather than relying on the store description alone, because a hand-applied solvent finish lives or dies on getting drying time, coat count and surface limitations exactly right. Everything below — what the product is, what stones it suits, how it is applied, and where it stops short of a sealer or a mechanical polish — is checked against that manufacturer document.

What Super Gloss Is — and What It Is Not
Per AKEMI's technical data sheet, Super Gloss is a solvent-containing product made of synthetic resins and waxes. It dries fast, intensifies the stone's natural color strongly, builds a high degree of gloss, resists yellowing over time, and leaves a closed, water- and dirt-resistant surface that is easy to keep clean because there is no open pore left for soil to sit in. The color is described as yellowish transparent, and the density is approximately 1.43 g/cm³.
What it is not matters just as much. Super Gloss is not a sealer: it does not impregnate the stone or block moisture penetration the way an AKEMI Pearl or Transformer Max impregnator does, and it carries no claim to stain protection. It is also not a floor finish and not a substitute for mechanical polishing on an open countertop field — the data sheet frames it specifically as a rework product for surfaces a machine could not or did not reach, not as a general-purpose coating for a whole slab. The TDS is also explicit that it is not scratch-proof, so it should not be expected to hold up to the abrasion a polished countertop surface sees in daily use.
The application area listed on the data sheet is specific: rough, ground, porous and absorbent surfaces on marble, granite, slate, Solnhofen slabs, sandstone, quartzite, terrazzo and fair-faced concrete, with particular emphasis on corners, edges, reliefs and frames that resist mechanical polishing. AKEMI is equally specific about where it does not belong — it must not go on glazed, fine-ground, polished or damp surfaces, and it is not suited for burnt products such as cotto, clinker or stoneware, where the surface chemistry is different from natural or cast stone.
That combination — hand application, strong gloss and color build, and a surface-rework rather than surface-protection role — is why Super Gloss shows up most often in monument work, restoration and conservation of carved stone, and in showroom sample preparation, where a fabricator needs a small, detailed or irregular surface to read as finished without running it through a polishing line.
Practical Guide: Surface Prep, Application and Drying
Getting the Surface Ready
The data sheet's first instruction is cleaning, and it is not a minor step: the surface must be clean, totally dry and free of any residual layer before Super Gloss goes on. AKEMI's own cleaning line — stone cleaner, concrete film remover, rust remover, wax stripper, oil and grease remover, graffiti remover — is named as the recommended prep path depending on what is soiling the stone, with a firm instruction to rinse thoroughly with water after cleaning and let the surface dry completely before any protective product goes on. Applying Super Gloss over residual cleaner, wax or moisture traps that layer under the lacquer and shows up as cloudiness or poor adhesion.
Because the surfaces this product targets are rough, ground or otherwise porous, dust is the other variable worth checking before application: a freshly ground relief or a sawn edge can carry fine stone dust that a visual check alone misses. A final wipe with a dry, lint-free cloth immediately before application, in addition to the wash-and-dry cleaning step, keeps that dust out of the finish.
The data sheet's list of compatible AKEMI cleaners is also a useful map of what kind of soiling a shop is likely to encounter before a Super Gloss application: a monument that has sat outside may need the algae and moss remover or the rust remover before anything else, while a freshly fabricated piece coming off the saw is more likely to need only a general stone cleaner to pull cutting residue and handling grime off the surface. Matching the cleaner to the actual soiling, rather than defaulting to one product for every job, keeps the prep step from leaving its own residue behind.
Applying It Thin, and Letting It Dry
Super Gloss is applied undiluted, in a thin, even layer, using a brush, paint roller or lint-free cloth — whichever gives the best control for the shape of the surface, since a carved relief and a flat frame edge do not take the same applicator equally well. AKEMI's data sheet gives a drying window of 10 to 60 minutes depending on temperature, and for very absorbent surfaces it directs a second coat once the first has set. Direct sun and humidity should be avoided while the coating dries, since both can affect how evenly the resin and wax film levels out.
A thin first pass matters more than it sounds: because the product is solvent-based and dries by evaporation rather than by chemical cure, a heavy single coat tends to dry unevenly at the surface while staying soft underneath, which is exactly the kind of result the two-coat method on absorbent stone is designed to avoid. Tools are cleaned with AKEMI Nitro-Dilution per the data sheet, and any cured Super Gloss that needs to come off the stone itself — because of a misapplication or a change of plan — is removed with AKEMI Universal Dilution rather than a generic solvent.
Working order matters on a piece with several distinct surface types, which is common on carved or relief work: start with the most absorbent, roughest areas first, since those are the surfaces most likely to need the second coat the data sheet calls for, and finish on any lightly ground transition zones last, once the applicator and technique are dialed in from the rougher sections. That sequencing also means any drips or runs that land on a not-yet-coated adjacent area can still be wiped off cleanly before they skin over.
| Finishing Method | How It Is Applied | Best Suited To |
|---|---|---|
| AKEMI Super Gloss | Brush, roller or lint-free cloth, undiluted, thin coat(s); dries 10–60 min per the TDS | Corners, edges, reliefs and frames mechanical polishing cannot reach; interior use |
| Self-polishing varnish (general category) | Hand-applied, builds gloss through multiple thin coats over time | Chiseled or textured edges, general detail work |
| Mechanical polishing | Diamond pad sequence on a wet polisher, machine or hand | Open, flat or gently curved fields a pad can reach |
Spotlight: AKEMI Super Gloss, 750 mL brings a machine-grade gloss to the corners and reliefs a polisher cannot touch — apply it thin, let it dry 10 to 60 minutes per the data sheet, and recoat once on absorbent stone.
Advanced and Trade-Specific Notes
Monument and memorial work is one of the clearest fits for this product. Carved lettering, relief panels and chamfered edges on upright memorials routinely have surfaces a polishing wheel cannot register against without rounding over the detail that makes the carving legible. A thin, hand-applied lacquer that intensifies color and builds gloss without touching the stone with an abrasive is the only practical way to finish that kind of detail work to a showroom-level sheen.
Restoration work on older stone — building facades, column capitals, weathered frames — runs into the same geometry problem on a larger scale, compounded by the fact that aged stone is often more porous than quarry-fresh material. The data sheet's direction to apply a second coat on very absorbent surfaces is particularly relevant here, since older, weathered stone will often soak up the first pass faster than a fresh-cut sample would.
Showroom sample preparation is a third use worth naming directly: a small sample chip or an edge-detail display piece benefits from the same hand-finished gloss, since a fabricator does not want to run a polishing line for a single display piece when a brush and a few minutes of drying time achieve a comparable look on the areas that matter for presentation.
Worth knowing before comparing products: AKEMI's two other gloss-building items in this family serve different jobs. The Tenax Luxor self-polishing varnish spotlight covers a competing brand's approach to chiseled-edge coating, while Akemi Liqui Polish Universal and Akemi Polishing Fluid No. 10 are both restoration-and-maintenance polishes meant to refresh an already-polished surface rather than rework a rough one — Super Gloss is the one of the three built to go on raw, unpolished stone.
On engineered and artificial stone, the data sheet's inclusion of "artificial stones" in its application area is worth reading precisely: it covers cast and composite surfaces that share the same rough, ground or porous condition as the natural stones listed, not every engineered surface regardless of finish. A factory-polished engineered slab is outside the product's intended use for the same reason a polished natural stone is — the closed, glazed surface it already has is exactly the condition the data sheet excludes. The product's value on artificial stone shows up on cut edges, ground returns and any area where the factory finish was removed during fabrication.
Ventilation, PPE and Long-Term Care
As a solvent-containing coating, Super Gloss needs the general precautions any solvent-based finish requires: work in a ventilated area, avoid prolonged skin contact, and keep solvent-sensitive materials — certain plastics, rubber and lacquered surfaces — out of the work area, since the data sheet specifically flags that those materials can be affected by nearby solvent exposure. AKEMI recommends its own Liquid Glove product to protect hands during application; a stone shop without that specific item on hand should default to solvent-resistant gloves and the eye protection any solvent handling calls for. The full safety data sheet should be read before use, and Dynamic Stone Tools' general PPE guide covers the broader respirator and glove selection logic that applies to solvent work in a stone shop.
Durability outdoors is limited according to the data sheet, which recommends AKEMI's Color Intensifier instead for exterior applications; Super Gloss should be treated as an interior finish, and work destined for permanent outdoor exposure needs a different product in the AKEMI line. Indoors, the closed surface it creates is described as easy to care for — AKEMI names its own Mild Stone Soap or Crystal Clean as the recommended regular cleaners once the lacquer has cured, rather than an abrasive scrub that could dull the gloss.
Shelf life is two years from the data sheet, provided the product is stored in a cool, frost-free place in its original, tightly sealed container; a partially used bottle left open or exposed to temperature swings in an unheated shop will not hold that full window. Because the container holds a flammable solvent base, waste disposal should follow the data sheet's direction to fully empty the container before disposal rather than discarding a partially full bottle.
Over the life of a bottle, the practical maintenance point is simple: keep the cap tight between uses, store it away from heat sources and open flame given the solvent base, and do a small test patch on an inconspicuous area before a full application on any stone type not already proven with this product, since porosity and surface texture vary enough between stones that a test patch catches a poor match before it reaches a visible surface.
Free Tool
Free Guides & Tools Hub — find the full lineup of restoration, sealing and finishing guides Dynamic Stone Tools publishes before picking a lacquer, sealer or polish for your next stone surface.
Open the Guides & Tools Hub →Finish What the Polisher Cannot Reach
Stock AKEMI Super Gloss alongside the rest of the sealing and restoration line for the edges, reliefs and frames every job eventually needs by hand.
Shop Sealers & Restoration →