Skip to Content

Tenax Universal Color Paste: Tinting Polyester and Epoxy Spotlight

October 3, 2026 by
Dynamic Stone Tools

Every fabricator has seen it: a tight, flat seam on a Bianco Carrara island that still reads from across the room because the glue line is a shade too gray, or a laminated edge on a gold granite where the joint shows as a thin amber stripe. The cut was good, the polish was good, and the customer still notices the seam. Most of the time the problem is not the adhesive itself but the color that went into it. Getting that color right is a matter of having the right base pigments on the bench and a repeatable way of dosing them, every single job.

This spotlight looks at Tenax Universal Color Paste, a concentrated pigment paste made for tinting polyester, epoxy and acrylic stone adhesives. Tenax sells it in ten base colors, and the idea is simple: add it to the glue a drop at a time, blend colors when one alone will not do, and keep the total under a firm limit so the adhesive still cures properly. Below we cover what the paste is, the full color and part-number lineup, how to dose it by weight, a matching routine that holds up on real jobs, and the safety data you should read before opening a bottle.

Tenax Universal Color Paste

What Tenax Universal Color Paste Is and Where It Fits

Tenax describes the product as a universal coloring paste, meaning a pigment concentrate rather than a tinted adhesive. You do not glue anything with it. You mix it into the adhesive you already use so that the cured joint, fill or lamination blends with the stone around it. The listing names three compatible adhesive families: polyester, epoxy and acrylic. That covers the knife-grade and flowing polyesters most shops use for laminations and fills, the two-part epoxies used for seams and structural repairs, and acrylic adhesives where a shop runs them. One set of pigments therefore serves the whole glue shelf.

The paste itself is soft and smooth, with a listed viscosity of 40,000–60,000 cps at 77°F (25°C). In practical terms it is thick enough that it does not run out of the nozzle on its own, but loose enough to fold into a puddle of glue in a few strokes of a putty knife. Tenax says it mixes into the adhesive quickly and evenly, which matters because streaks of unmixed pigment show up as dark threads in a polished seam. The bottle is an easy-squeeze design with a precision drop nozzle and a twist-lock, spill-proof cap, so a single drop is a realistic unit of measure.

Tenax lists the paste as UV stable for both indoor and outdoor work. That matters on exterior steps, outdoor kitchens and facade repairs, where a joint that fades or shifts in sunlight becomes visible within a season. Two independent retailer listings for the same Tenax product carry the same UV-stable, indoor-and-outdoor claim and the same polyester, epoxy and acrylic compatibility, which matches the manufacturer data. It does not change how the base adhesive itself behaves outdoors, so the glue you tint still has to be suitable for exterior use on its own merits. The paste colors the joint; it does not upgrade the resin.

Why does a dedicated stone pigment matter at all? Many clear polyester and epoxy adhesives are not water-white; repair guides from both the trade press and stone-repair suppliers point out that transparent products often carry a slight amber cast. On a white marble or a light quartz that amber tone is exactly what makes the seam visible. A small amount of White or Buff paste can push the joint back toward the stone, while Black, Grey and Brown handle the darker granites. Having ten bases on the bench means you correct the color the glue starts with instead of living with it.

Colors, Part Numbers and Dosing by Weight

Tenax offers ten colors in 2 oz bottles and nine in 8 oz bottles; Blue is the one color sold in the 2 oz size only. There are also two kits: a Set of 10 Colors with one 2 oz bottle of each color, and a Set of 6 Colors. The table below lists the Tenax color code, both part numbers and the relative density from each color’s Safety Data Sheet. Keep the density column in mind, because it changes how much paste by volume reaches the weight limit. The 8 oz bottle holds the same paste as the 2 oz, only more of it, so it suits a shop that runs one color every day.

ColorTenax Code2 oz Part No.8 oz Part No.Relative Density (SDS)
Black107101H3588BLACK1H3589BLACK1.12
White100091H3588WHITE1H3589WHITE1.74
Red104101H3588RED1H3589RED1.08
Red Brown104071H3588RB1H3589RB1.45
Yellow103011H3588YELLOW1H3589YELLOW1.3
Green105081H3588GREEN1H3589GREEN1.18
Brown111331H3588BROWN1H3589BROWN1.26
Blue108021H3588BLUE— (2 oz only)1.43
Grey106091H3588GREY1H3589GREY1.62
Buff101311H3588BUFF1H3589BUFF1.8
Set of 10 Colors (one 2 oz of each)—1H3588SET—See each color
Set of 6 Colors—1H3585ASET—See each color

Respect the 2–3% Ceiling

The single number on this listing to tape to the wall is the maximum dosage: no more than 2–3% of the adhesive weight, counting every color in the mix together. Tenax warns that too much pigment can reduce the quality of the glue, and retailer listings for the same product repeat the 2–3% ceiling. In shop terms, 100 grams of knife-grade polyester can take roughly 2 to 3 grams of total paste. If you blend White, Buff and a touch of Black, those three amounts add up toward the same cap. A cheap gram scale on the mixing bench turns this from guesswork into a habit.

The density column explains why weighing beats eyeballing. Relative density runs from 1.08 for Red to 1.8 for Buff, so a given squeeze of Buff, White (1.74) or Grey (1.62) weighs far more than the same squeeze of Red or Black (1.12). A light-stone mix heavy on White and Buff reaches the weight limit with noticeably less paste by volume than a dark mix built on Black. Fabricators who learned to tint by drops on dark granite sometimes overload light marble mixes for exactly this reason. If a light mix looks like it needs more paste than usual, weigh it before adding another drop.

Tint the Resin Before You Catalyze

The Tenax instructions run in a clear order: dispense the adhesive you need, add color a drop at a time, blend colors as needed, mix until even, then use the tinted adhesive according to that adhesive’s own instructions. A European distributor of the paste states it plainly, advising that you color the adhesive first and add the hardener once you reach the shade, and stone-repair kit instructions from another supplier tint Part A before combining it with Part B. The reason is time. Once hardener goes in, the pot life clock is running, and matching color against a gelling glue leads to rushed, streaky work.

A Repeatable Matching Routine

Start light and build. Stone-repair suppliers agree on adding pigment in very small increments and stirring hard after each addition, because it is easy to add color and nearly impossible to take it out without making a bigger batch. With Tenax paste, that means one drop, mix, look, then decide. Begin with the dominant background color of the stone, not the flecks. On a typical gray granite that is usually Grey or a little Black into White; on a creamy limestone it might be Buff with a trace of Yellow. Build the base first and leave the accents for later.

Judge the cured color, not the wet one. Both a stone-repair guide and a trade-magazine interview with repair specialists make the same point: wet resin can read darker, glossier and more saturated than it does once it cures, and a match that looks perfect in the cup can dry to a different color or sheen. The fix is a test. Mix a small amount of the tinted adhesive with hardener, smear it on a scrap of the same stone or a piece of tape, and let it cure before you commit the real batch. It costs a few minutes and saves pulling a seam.

Keep a reserve. Repair-kit instructions recommend setting aside some untinted or lightly tinted material, and repair pros interviewed in the trade press describe returning to an earlier base and adjusting it rather than starting over. Before catalyzing, pull a small dab of your tinted base onto a separate spot of the mixing board. If the test sample cures too dark, you can lighten from that reserve with White or Buff; if it cures too flat, you can split the reserve and add a second color for movement. Uncatalyzed, the reserve stays workable while you decide.

Check your light. Metamerism is the color-science term for two surfaces that match under one light source and drift apart under another, and it is well documented in color references. A seam tinted under cool shop LEDs can look different under warm kitchen bulbs or daylight through a window. When you can, compare your cured sample to the slab in more than one light, and carry it out of the shop if needed. For an island that will sit near a large window, daylight is the light the customer will use to judge your work.

Pull back a color that went too far. Basic color mixing says a hue that is too strong can be toned down by adding a small amount of its complement from the opposite side of the color wheel, and stone-repair instructions apply the same principle to resin tints. In practice, a mix that went too red can be calmed with a trace of Green, and a mix that went too yellow can be pulled back with a touch of Blue or Grey. Use very little, check again, and remember that every corrective drop counts toward the 2–3% total.

Spotlight: Tenax Universal Color Paste gives you ten base colors (Black, White, Red, Red Brown, Yellow, Green, Brown, Blue, Grey and Buff) that work in polyester, epoxy and acrylic stone adhesives. It is UV stable for indoor and outdoor work, doses by the drop from a precision nozzle, and keeps at least 12 months in the closed original container at 64–77°F (18–25°C). Start with the Set of 10 Colors (1H3588SET) and add 8 oz bottles of the colors you go through fastest.

Advanced Matching Tips from the Bench

Separate the background from the pattern. Most stones are not one color; they are a field color with veins, crystals or flecks on top. One stone-repair guide recommends keeping the fleck colors out of the main batch and working them into the wet fill separately, and repair-kit instructions likewise describe adding lighter and darker tints from a reserve in small amounts and in different directions. For a granite chip fill, that means a base matched to the dominant mineral, then a few streaks of Black or White drawn in with the tip of a blade before the glue gels. Restraint looks more natural than a busy patch.

Write down what works. A shop that matches the same popular quartz or granite every week should not be rediscovering the recipe every week. Record the stone name, the adhesive, the total adhesive weight and the grams or drops of each Tenax color. Because Tenax gives every paste a fixed color code, such as 10710 for Black or 10131 for Buff, the recipe card can name the exact pigment, not just a color word. When a second installer picks up the job, the recipe travels with it, and the seams on a large project stay consistent from the first slab to the last.

Safety Data, Storage and Shelf Life

Every color carries the GHS signal word Warning, and every color lists H227, Combustible liquid, and H317, May cause an allergic skin reaction, in Section 2 of its SDS. Beyond those two, the hazards differ by color. Black and Brown add H351, Suspected of causing cancer. Grey and Buff add H361, Suspected of damaging fertility or the unborn child. White, Red, Red Brown, Yellow, Green and Blue list only H227 and H317. Black and Brown, which contain carbon black, also carry a California Proposition 65 warning; per their SDS, the other eight colors contain no Proposition 65 chemicals. Read the SDS for each color you stock before use; Dynamic Stone Tools links each one from the product page.

The skin-sensitizer warning on every color is the one that shapes daily habits. Allergic skin reactions tend to build with repeated exposure, so a mixer who handles pigment and resin bare-handed every day is the person most at risk. Wear chemical-resistant gloves while dispensing and mixing, keep paste off the bottle threads so caps close cleanly, and clean up smears on the bench rather than leaving them to be picked up later on a sleeve. The listing closes with a simple instruction worth repeating to every new hire: wear appropriate PPE and read the SDS before use.

Storage is straightforward but strict. Tenax lists a shelf life of 12 months in the closed original container at 64–77°F (18–25°C), kept away from heat, humidity and sunlight, and the instructions say to close the bottle right after use and keep the paste in its original container out of direct sunlight. In practice, that means not leaving bottles on a sunny windowsill or in a hot truck over summer. Because the paste is a combustible liquid, store it with your other resins and away from ignition sources, and keep the twist-lock caps fully closed.

To build out a full adhesive station, browse the coloring pastes collection for other tinting options, the polyester, vinyl ester and acrylic adhesives for knife-grade and flowing glues, and epoxy adhesives for seams and structural repairs. The full Tenax lineup at Dynamic Stone Tools also includes cleaners, sealers and color enhancers if you prefer to keep the whole chemical shelf from one manufacturer. You can order the paste in single colors or as a set directly from the Universal Color Paste product page.

Make Your Seams Disappear

Stock Tenax Universal Color Paste alongside the polyester and epoxy adhesives your shop already uses. Dynamic Stone Tools carries single colors, 8 oz refills and complete sets for professional fabricators.

Shop Coloring Pastes →

Free Tool

Chemical Advisor — Tell it the stone and the job, and it points you to the right adhesive, sealer or cleaner, so you know which glue you are tinting before you open a pigment bottle.

Open the Chemical Advisor →
Dynamic Stone Tools October 3, 2026
Share this post
Archive