$ 111.89
$ 111.89
$ 111.89
-
Brand
-
Color
| Brand: Akemi |
Akemi Akepox 2030 Quick Mix Two-Component Epoxy Adhesive
AKEPOX® 2030 is AKEMI’s creamy, solvent-free, two-component (Part A + Part B) epoxy adhesive built for the stone-fabrication industry. Its filled, creamy body gives it excellent vertical stability — it holds on uneven or upright joints without sagging — while its relatively fast cure gets parts back into production quickly. The result is an extremely weather-resistant, dimensionally stable, high-strength bond on marble, granite, porcelain and ceramics, engineered stone, terrazzo, concrete, and metals. Supplied here in the 400 mL Quick Mix cartridge for clean, pre-metered dosing through a static mixing nozzle.
- Creamy, non-sag body — good vertical stability, bridges relatively uneven surfaces
- Relatively fast hardening — bonded parts movable in about 3–5 hours
- Solvent-free — extremely low shrinkage and low tension in the bond line
- Weather- and alkali-resistant — very well suited to bonding concrete
- Cartridge system — easy, accurate dosing and mixing
- Tintable with AKEPOX® Colouring Pastes / Concentrates (up to 5%)
This product is offered in the following options — select your choice above:
| Color | Item Reference |
|---|---|
| Transparent | EPOX.10600 |
| Gray Green | EPOX.10604 |
| Brick Red | EPOX.10605 |
| Light Ivory | EPOX.10614 |
| Property | Detail |
|---|---|
| Brand | Akemi |
| Manufacturer | AKEMI GmbH, Nuremberg, Germany |
| Product Type | Two-component (2K) epoxy adhesive |
| Chemical Basis | Epoxy resin with fillers and a modified polyamine hardener, solvent-free |
| Consistency | Creamy, non-sag — good vertical stability |
| Colour | Green-grey, brick-red, black, light ivory (tintable) |
| Mixing Ratio | 2 : 1 (Part A : Part B) by volume or weight |
| Working / Pot Life | Approx. 20–30 min at 68°F (20°C) |
| Parts Movable After | Approx. 3–5 hours at 68°F (20°C) |
| Ready to Process After | Approx. 8–10 hours at 68°F (20°C) |
| Full / Maximum Strength | After 7 days at 68°F (20°C) |
| Bending Strength | 7,250–8,700 psi (50–60 N/mm², DIN EN ISO 178) |
| Tensile Strength | 2,900–4,350 psi (20–30 N/mm², DIN EN ISO 527) |
| Compressive Strength | 10,150–11,600 psi (70–80 N/mm², DIN EN ISO 604) |
| Density (A & B) | Approx. 1.52 g/cm³ (12.7 lb/gal) |
| Water Absorption | Less than 0.5% |
| Thermal Stability (cured) | −4°F to 140–158°F (−20°C to 60–70°C) under load; up to 212–230°F (100–110°C) without load |
| Minimum Application Temp. | 50°F (10°C) — will not fully harden below this |
| Tool Cleaner | AKEMI® Nitro-Thinner (uncured adhesive) |
| Shelf Life | At least 24 months stored dry and cool at 41–77°F (5–25°C) in the closed original container |
| Interior/Exterior | Interior, Exterior |
| Material | Natural Stone, Quartz, Concrete, Metals, Fiberglass |
- Relatively fast hardening for quicker turnaround
- Creamy consistency gives good vertical stability and lets you join relatively uneven surfaces
- Extremely low shrinkage during curing, so tensions in the bonding layer stay low
- Extremely weather-resistant, dimensionally stable bonds with a small tendency to fatigue
- Very good alkali stability — very well suited to bonding concrete
- Solvent-free: excellent for gas-impermeable materials and materials sensitive to solvents (e.g. expanded polystyrene, ABS)
- Good adhesion even on slightly humid stone; good electrical insulating property
- Coated metal parts are very well protected against corrosion
- Not liable to crystallize — trouble-free storage and processing
- Easily coloured with AKEPOX® Colouring Pastes or Concentrates (up to max. 5%)
Recommended for bonding & gluing:
- Natural stone — marble and granite
- Porcelain and ceramics
- Artificial / engineered stone and building materials (terrazzo, concrete)
- Metals — iron, steel, aluminum (also protects them against corrosion)
- Plastics — rigid PVC, polyester, polystyrene, ABS, polycarbonate
- Paper, wood, and glass
Not suitable for: polyolefins (polyethylene, polypropylene), silicone, fluorohydrocarbons (Teflon/PTFE), flexible PVC, flexible PU, and butyl rubber.
For load-bearing construction parts, observe the relevant standards (e.g. DIN 18516 Part 1 & Part 3, DIN 2304).
- Thoroughly clean and slightly roughen the surfaces to be bonded.
- Cartridge: remove the clasp, insert the cartridge in the gun and work the grip until material emerges from both openings, then screw on the mixing nozzle. Cans: thoroughly mix 2 parts of Part A with 1 part of Part B (by volume or weight) until a uniform, homogeneous colour is achieved, using two separate spatulas for resin and hardener.
- If desired, add AKEPOX® Colouring Pastes or Concentrates — up to a maximum of 5%.
- The mixture stays workable for approx. 20–30 minutes at 68°F (20°C). Working time shortens in heat and lengthens in cold (approx. 50–60 min at 50°F / 10°C; 8–12 min at 86°F / 30°C).
- Bonded parts may be moved after approx. 3–5 hours, further processed after approx. 8–10 hours, and reach maximum stability after 7 days (all at 68°F / 20°C).
- Clean tools with AKEMI® Nitro-Thinner before the adhesive cures. Curing is accelerated by heat and delayed by cold.
- Keep the correct 2:1 mixing ratio — excess resin or hardener acts as a softener and can discolor the bond edges.
- Do not apply below 50°F (10°C): the adhesive will not harden sufficiently.
- The cured adhesive is liable to yellow in sunlight — not suited for fillings or visible joints on light-coloured or white surfaces.
- Do not use adhesive that has already thickened or begun to jelly.
- Grind metal surfaces shortly before bonding to avoid a loss of adhesion.
- Cured adhesive can only be removed mechanically or with high heat (above 392°F / 200°C), not with solvents.
- For cartridges, use AKEMI® original mixing nozzles only. For professional use only.
- Industrial chemical product — use only in well-ventilated areas and wear chemical-resistant gloves and eye protection. Always consult the AKEMI Safety Data Sheet (SDS) before use.
Industrial chemical product. Use only in well-ventilated areas. Wear chemical-resistant gloves and eye protection. Consult the AKEMI Safety Data Sheet (available from the manufacturer or stein.akemi.de) before use. Technical values are manufacturer figures at 68°F (20°C) and may vary with jobsite conditions.